Pierce Leak Pros
Get Estimate

Under Slab Leak Detection in Fort Pierce

Pinpoint the leak before you break concrete


Under Slab Leak Detection in Fort Pierce starts with finding the exact break, not guessing at it. If your water bill jumped, a hot spot is spreading across the floor, or you hear water running with every fixture off, we bring acoustic listening discs and thermal imaging to your slab and locate the failure within inches. We have served St. Lucie County since 2000, and we test the line before we leave.

Close-up of an unfinished multi-level concrete building with steel reinforcements.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed 26+ Years Trusted in Fort Pierce

What Our Under Slab Leak Detection Includes

Every detection visit includes the full diagnostic sequence, not just a listen-and-leave. We isolate the system, test both hot and cold sides, scan the slab, and confirm the location before we quote a repair. If the leak turns out to be outside the slab, we tell you that too and point you to the right service.

Hot and Cold Pressure Test

We isolate and charge both supply sides with a pressure testing gauge and watch for a drop. This tells us which line is losing water and rules out fixtures, the water heater, and irrigation before we focus on the slab.

Acoustic and Thermal Scan

An acoustic listening disc and a FLIR thermal imaging camera cover the suspect area. We mark the readings on the floor so you can see where the sound and temperature anomalies line up.

Location Confirmation

A moisture meter and, where accessible, a pipe inspection camera or tracer gas detector confirm the break. We do not quote a repair off a single reading; the location is verified before we mark it.

Mark-Out and Written Finding

We mark the break on the floor, photograph it, and give you a written finding with the cause and the recommended repair. That document is useful for insurance and for any second opinion you want to get.

Repair Quote On Site

You get a price for the repair before any concrete is cut, including the patch and the pressure test afterward. If epoxy pipe lining fits the line, we quote that option alongside a spot repair.

What Under Slab Leak Detection in Fort Pierce Really Involves


Under Slab Leak Detection in Fort Pierce is the process of locating a pressurized water or drain line failure beneath a concrete floor without tearing up the slab to find it. We start by isolating the system with a pressure testing gauge, then listen through the concrete with an acoustic listening disc and scan the floor surface with a thermal imaging camera. A hot water line leak shows up as a warm patch; a cold line shows as a pressure drop that will not hold. The goal is simple: mark the break within a few inches so the repair is a small, targeted cut instead of a room-wide demolition.

Fort Pierce homes sit on some of the most variable soil in St. Lucie County, and that is where most of these leaks begin. Shifting sand and shell hash move copper pipe until a fitting cracks or a pinhole opens, and the slab hides the evidence until the water bill doubles. If you have been searching for under slab leak detection near me Fort Pierce FL and getting nothing but guesses, we can pressure-test the system and tell you which line is losing water in about an hour. That is the difference between a repair and a remodel.

How Our Detection Process Works

Every call follows the same sequence, whether it is a hot water line under a Lakewood Park ranch or a commercial slab on US-1. You get a clear answer on where the leak is and what the repair involves before we cut anything.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

Acoustic Listening Disc

Amplifies the sound of water escaping a pressurized pipe so we can narrow the break to a small area through concrete, tile, or vinyl flooring.

FLIR Thermal Imaging Camera

Maps temperature differences across the slab. A hot water line leak shows as a warm plume, and a cold line often shows as a cool spot.

Pressure Testing Gauge

Isolates and charges the hot and cold sides to confirm which line is losing water before we scan the slab.

Electronic Leak Detection Wand

Picks up the high-frequency sound of a pinhole or crack and helps confirm the acoustic disc reading in noisy environments.

Tracer Gas Detector

Introduces a safe tracer gas into the line and detects where it escapes, which is useful when acoustic readings are ambiguous.

Pipe Inspection Camera

Confirms the line material and the break location from inside the pipe where access allows, including copper, PEX, and CPVC.

Moisture Meter and Infrared Thermometer

Confirms the wet reading at the marked spot and verifies the temperature anomaly before any concrete is cut.

Methods & Standards

System Isolation and Pressure Testing

We shut off the supply, isolate the hot and cold sides, and charge each with a pressure testing gauge. A drop on one side tells us which line is failing and rules out fixtures, irrigation, and the water heater before we focus on the slab.

Acoustic and Thermal Correlation

We combine the acoustic listening disc with the FLIR thermal camera and look for where the sound and temperature readings agree. Correlating two methods is how we avoid marking a spot based on a single ambiguous reading.

Tracer Gas Confirmation

When acoustic and thermal readings are close but not conclusive, we introduce a safe tracer gas into the isolated line and detect where it escapes. This is common on deeper slabs and under tile where sound transmission is poor.

Epoxy Pipe Lining Evaluation

For copper lines with multiple pinholes, we evaluate whether epoxy pipe lining is a fit before recommending a spot repair. Lining can restore the line from the inside and avoid repeated cuts in the same slab.

When to Call for Under Slab Leak Detection

01

A 1970s block home near Downtown Fort Pierce with copper lines and a water bill that jumped $80 in one month.

What we do: We isolate the hot and cold sides, pressure-test both, and run an acoustic scan across the tile. Copper pinholes in older Fort Pierce homes are common, and the disc usually narrows the location within an hour.

→ The break is marked, the repair is quoted, and the homeowner avoids a full-floor demolition.

02

A newer PEX build in Fort Pierce South with a warm spot spreading across the hallway floor.

What we do: A thermal imaging camera maps the warm plume and a moisture meter confirms the reading. We mark the spot and check the manifold to rule out a fitting failure at the source.

→ The hot water line leak is located to within a few inches and repaired with a small cut and patch.

03

A rental property in Lincoln Park where the tenant hears water running at night with all fixtures off.

What we do: We pressure-test the system, listen with the acoustic disc, and confirm the line with a pipe inspection camera where accessible. The property manager gets a written finding for the owner.

→ The leak is located and repaired, and the owner has documentation for the insurance file.

04

A commercial building on US-1 with a spike in the water bill and no visible water in the unit.

What we do: We isolate the domestic supply from the irrigation and fire lines, then scan the slab with thermal and acoustic tools. Commercial slabs often hide the break under tile or carpet, and the camera confirms the line.

→ The break is pinpointed after hours, and the repair is scheduled without closing the business.

How Under Slab Leak Detection Runs in Fort Pierce

Fort Pierce sits on sandy, shelly soil that moves with the water table, and that movement is hard on copper pipe. Homes built before the 1980s near Downtown Fort Pierce and Lincoln Park usually have copper supply lines that develop pinholes where the soil shifts, while newer builds in Fort Pierce South and White City often use PEX tubing with fitting failures instead. The summer rainy season raises the water table, which can mask a small leak and make a moisture meter read wet everywhere, so we lean on pressure testing and acoustic listening rather than moisture alone. Florida Plumbing Code and St. Lucie County permitting apply to the repair, and we pull permits when the scope requires it. If you have been searching for under concrete slab leak detection Fort Pierce, the sequence is the same whether your home is on a raised slab or a mono-slab: isolate, listen, scan, confirm, mark. We also handle under foundation leak detection Fort Pierce FL calls where the water is entering at the slab edge rather than under the middle of the floor.

Neighborhoods We Serve

  • Lakewood Park

    A mix of older block homes and newer builds, so we carry both copper and PEX repair materials on the truck for the same-day calls.

  • Downtown Fort Pierce

    Historic homes with original copper lines and mature landscaping. Root intrusion and soil movement are common causes of under slab pipe leaks here.

  • Fort Pierce South

    Newer PEX construction where fitting failures and manifold issues are more common than pipe corrosion. We check the manifold before opening the slab.

  • White City

    Larger lots with longer service lines, so we isolate the yard line from the slab before assuming the leak is under the house.

  • Lawnwood

    Older housing stock near the hospital corridor, with copper lines that often show pinhole corrosion after decades in local soil.

Local Conditions We Plan For

  • Sandy, shifting soil and a high water table

    Soil movement cracks fittings and opens pinholes in copper, and the high water table can mask a small leak on a moisture meter. We rely on pressure testing and acoustic listening to confirm the location.

  • Summer rainy season saturation

    From June through September, the ground stays wet and moisture readings become less reliable. Thermal imaging and tracer gas help confirm the break when the soil is saturated.

  • Older copper housing stock

    Homes built before the 1980s are more likely to have copper pinholes, and multiple leaks in the same line may point to epoxy pipe lining instead of repeated spot repairs.

Water Bill Spike in Lakewood Park

Before

A Lakewood Park homeowner saw the water bill climb from $60 to $190 in one month with no visible leak. Two other companies quoted a full-floor demolition to find it, and the homeowner held off.

After

We pressure-tested the system, located a hot water line leak within 8 inches using the acoustic disc and thermal camera, and repaired it with a 3-square-foot cut. The bill returned to normal the next cycle, and the concrete patch matched the surrounding floor.

Maintenance: We recommended a yearly pressure test on the hot side and a check of the water heater anode, since the same soil conditions that caused this pinhole will affect the rest of the copper line over time.

Before

A homeowner in Fort Pierce South noticed a warm patch spreading across the hallway tile and a faint sound of running water at night. The floor was still dry, so the leak had not reached the surface yet.

After

The FLIR camera mapped the warm plume, the moisture meter confirmed the reading, and we pinpointed a PEX fitting failure under the slab. The repair was a small cut and patch, and the line held pressure at 80 psi before we closed the floor.

Maintenance: We suggested checking the manifold connections annually and watching for any new warm spots, since PEX fitting failures can appear at more than one location in the same system.

Before

A property manager in Lincoln Park had a tenant hearing water running at night with all fixtures off. The water bill was climbing, and the owner wanted documentation before authorizing any repair.

After

We isolated the system, confirmed a copper pinhole under the slab with the acoustic disc and pipe inspection camera, and provided a written finding with photographs. The repair was completed in one day, and the owner had the documentation for the insurance file.

Maintenance: We set up an annual pressure test for the property and flagged the remaining copper line for a future epoxy pipe lining evaluation to avoid repeat cuts in the same slab.

Problems We Solve With Under Slab Leak Detection

Most slab leaks announce themselves through the bill or the floor long before water reaches the surface. These are the calls we run most often in Fort Pierce, and each one has a specific detection approach.

Problem

Water bill doubled with no visible leak

A pinhole under a slab can waste hundreds of gallons a day, and the bill keeps climbing until the line is isolated and tested. Left alone, the water softens the soil under the slab.

Our Fix

We isolate the hot and cold sides with a pressure testing gauge, find which line is losing water, and pinpoint the break with acoustic and thermal tools. Most of these calls are resolved in a single visit.

Problem

Hot spot on the floor or warm tile

A warm patch usually means a hot water line is leaking under the slab. The heat draws moisture up through the concrete and can warp vinyl or lift tile if it runs long enough.

Our Fix

A FLIR thermal imaging camera maps the temperature plume and narrows the break to a small area. We confirm with a moisture meter and mark the spot before quoting the repair.

Problem

Sound of running water with fixtures off

Constant running water with everything shut off points to a pressurized line losing water under the slab or in the yard. Ignoring it runs up the bill and can undermine a foundation.

Our Fix

We pressure-test the system and use an acoustic listening disc to trace the sound to its source, whether that is under the slab or in the service line. You get a location, not a guess.

Problem

Cracks in floor tile or baseboards

Soil movement from a long-running leak can shift the slab and crack tile or pull baseboards away from the wall. By the time cracks show, the leak has usually been active for weeks.

Our Fix

We combine moisture readings with thermal imaging to separate a plumbing leak from settlement, then locate the pipe break if one is present. If the issue is structural, we tell you and point you to the right trade.

Why Pinpoint Detection Saves Money

Why Pinpoint Detection Saves Money

A slab leak is not the expensive part. Cutting the wrong square of concrete is. Accurate detection turns a demolition project into a two-foot repair, and it protects the flooring, cabinets, and baseboards you already paid for.

  • Smaller, Cheaper Repairs

    When we pinpoint a leak under concrete slab in Fort Pierce to within a few inches, the repair cut is typically 2 to 4 square feet instead of an entire room. That cuts concrete breaking, hauling, and patching costs, and it usually means one day of work instead of three.

  • Stop the Water Bill Bleed

    A pinhole under a slab can waste 200 to 500 gallons a day, which shows up fast on a Fort Pierce utility bill. Finding the under slab water leak in Fort Pierce early stops the loss at the source and gives you a documented cause before the bill climbs another month.

  • Protect the Foundation

    Water soaking into the soil under a slab softens the bearing surface and can lead to settlement cracks in the walls and floor. Catching an underground pipe leak early keeps the soil stable and avoids a foundation repair that costs many times what detection does.

  • No Guesswork, No Extra Holes

    We use a pipe inspection camera and tracer gas detector to confirm the line and the break before anyone picks up a saw. You get a marked location, a written finding, and a repair plan, not a crew opening three holes hoping to get lucky.

Licensed, Certified, and Reviewed

Licensed & Certified

  • Florida Licensed Plumbing Contractor — issued by State of Florida Department of Business and Professional Regulation
  • Florida Certified Plumbing Contractor — issued by State of Florida Department of Business and Professional Regulation
  • Backflow Prevention Certification — issued by State of Florida
  • OSHA Safety Certification — issued by Occupational Safety and Health Administration
  • IAPMO Certification — issued by International Association of Plumbing and Mechanical Officials

Verified Reviews

Google ★★★★★4.9

They found a hot water line leak under our slab in about an hour and marked it within a few inches. The repair cut was small and the patch looks like it was never touched. Water bill is back to normal.

Yelp ★★★★★4.8

Called on a Saturday with water running under the floor. They answered, came out the same day, and pressure-tested the system before doing anything. Clear price, no upsell, and the leak was exactly where they marked it.

BBB ★★★★★4.9

We manage rentals near downtown and have used them three times for slab leaks. Every visit came with a written finding and photos for the owner. Professional crew and they show up when they say they will.

Leak Detection Experience You Can Check

Pierce Leak Pros has been locating and repairing slab leaks in Fort Pierce since 2000, which is 26 years of working on the same soil, the same building codes, and the same housing stock. Our technicians hold Florida Licensed Plumbing Contractor and Florida Certified Plumbing Contractor credentials through the State of Florida DBPR, and we carry Backflow Prevention Certification and OSHA Safety Certification. We have pressure-tested thousands of slabs across St. Lucie County, from 1950s block homes near Downtown Fort Pierce to newer PEX builds in Fort Pierce South. That history is why we can usually tell you which line is failing before the camera comes out.

  • 26 years locating slab leaks in Fort Pierce and across St. Lucie County
  • Florida Licensed Plumbing Contractor and Florida Certified Plumbing Contractor on staff
  • Backflow Prevention Certification and OSHA Safety Certification current
  • Acoustic, thermal, and tracer gas equipment calibrated and carried on every truck
  • IAPMO Certification supporting code-correct repairs and epoxy pipe lining work
Get Started Today
Leak Detection Experience You Can Check

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

What pipes run under a slab foundation in a Fort Pierce home?
Most Fort Pierce slab homes have copper, PEX, or CPVC supply lines running beneath the concrete, plus a PVC drain line. Homes built before the 1980s are usually copper, which is prone to pinhole corrosion in local soil. Newer builds in Fort Pierce South and White City often use PEX tubing. We pressure-test each line separately to identify which one is losing water.
How do I tell if a leak is under the slab or inside a wall in Fort Pierce?
Start with the meter. Shut every fixture off and watch the flow indicator; if it moves, you have a pressurized leak. A hot spot on the floor or a water bill spike points under the slab, while a damp baseboard or musty smell points to a wall. We isolate the system with a pressure testing gauge to confirm which side is losing water before opening anything.
Can the exact location of an under slab leak be pinpointed in Fort Pierce?
Yes. Acoustic listening discs, thermal imaging cameras, and tracer gas detectors routinely narrow an under slab pipe leak to within a few inches. We confirm the spot with a moisture meter and, where accessible, a pipe inspection camera. That accuracy is why our repair cuts are usually 2 to 4 square feet instead of a full room tear-out.
Why is it hard to find a leak under a concrete slab in Fort Pierce?
Concrete is dense and hides both sound and moisture, and local soil movement can shift a pipe so the leak migrates from where it started. Water also follows the path of least resistance, so the wet spot on the floor is not always above the break. We combine pressure testing, acoustic listening, and thermal imaging to trace the actual source rather than the visible symptom.

Related Services

Slab Leak Detection

Our core slab leak detection service covers the same pressure testing and acoustic work as under slab leak detection in Fort Pierce, with a focus on confirming whether the loss is under the slab or in the service line. We document the finding and quote the repair in the same visit.

View Slab Leak Detection

Slab Leak Repair

Once we pinpoint the break, our slab leak repair crew cuts the marked area, replaces the failed section with copper or PEX, and pressure-tests before patching. Most residential repairs in Fort Pierce are completed in one day, including concrete patch and cleanup.

View Slab Leak Repair

Water Leak Detection

Water leak detection covers the whole system, including fixtures, irrigation, and the water heater, so we can rule out the easy causes before charging a slab. This is the service we run first when you are not sure where the water is going.

View Water Leak Detection

Underground Pipe Leak Detection

Underground pipe leak detection handles lines outside the slab, including yard service lines and pool plumbing. If your meter runs with the house shut off, this service finds the buried break before it undermines a driveway or patio.

View Underground Pipe Leak Detection

Foundation Leak Detection

Foundation leak detection focuses on water entering or moving under the structural slab, including cracks and settlement-related pipe damage. We combine moisture readings with thermal imaging to separate a plumbing leak from a drainage or waterproofing problem.

View Foundation Leak Detection

Emergency Leak Detection

Emergency leak detection is for active water, a spike in the water bill, or a hot spot that appeared overnight. We keep a 24/7 line open and dispatch for under slab leak detection in Fort Pierce when the water cannot wait until morning.

View Emergency Leak Detection

Get Under Slab Leak Detection in Fort Pierce Today

We answer the phone 24/7 and book same-day detection windows across St. Lucie County. Call with your water bill, your hot spot, or the sound you keep hearing, and we will bring the acoustic and thermal gear to your slab.

Call Now Book Detection

Call Pierce Leak Pros

If you have water where it should not be, call us. We answer the phone 24/7, and most standard calls get same-day service. Tell us what you are seeing and we will tell you what it takes to find it. Serving Fort Pierce and all of St. Lucie County from ZIP 34950.

Or call us right now at 1234567890 — we answer.

Pierce Leak Pros


  • Phone

    1234567890
  • Address

    3006 S US Hwy 1, Fort Pierce, FL 34982, USA, Fort Pierce, Florida

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call 1234567890 Get Quote
Call Quote