Pierce Leak Pros
Get Estimate
Repair TipsLocal Guides

Unexplained High Water Bill: How to Check for a Slab Leak


A sudden spike in your Fort Pierce water bill usually means a hidden leak. Here's how to test your meter, rule out the obvious, and confirm a slab leak before it damages your foundation.

PPierce Leak Pros ·November 2026 ·9 min read
Detailed view of a complex water meter setup embedded in a concrete wall.

An unexplained high water bill in Fort Pierce FL almost always means water is escaping somewhere between the meter and your fixtures - and if the meter keeps spinning with every faucet off, the leak is likely under your slab. The fastest way to confirm it is a 20-minute meter test: shut off every water-using appliance, note the meter reading, wait, and check again. If the dial moves, you have a live leak. This guide walks you through that test step by step, explains what else can spike a bill, and shows you when a slab leak is the real culprit.

Why Is My Water Bill So High in Fort Pierce FL?

A high water bill in Fort Pierce usually comes from one of four sources: a running toilet, an irrigation leak, a slab leak under the foundation, or a meter that needs recalibration. Fort Pierce Utilities Authority bills in 1,000-gallon increments, so a single leaking flapper valve can add 200 gallons a day - roughly 6,000 gallons a month - before you hear a sound. Slab leaks are quieter and more expensive because the water travels under your floor before it surfaces.

Homes built in the 1970s and 1980s across slab leak repair Downtown Fort Pierce FL are prime candidates. Copper supply lines under those slabs have been sitting in Florida's sandy, slightly acidic soil for 40-plus years. Pinhole corrosion turns into a steady drip, and the bill is often the first sign. We have run thousands of meter tests in this city, and the pattern is consistent: the older the neighborhood, the more likely the spike traces back to under-slab plumbing.

How to Read a Water Meter to Find a Leak in Fort Pierce

Reading a water meter to find a leak in Fort Pierce takes about 15 minutes and requires no tools. Your meter is in a concrete box near the street, usually under a round or rectangular lid stamped "water." Lift the lid with a screwdriver, and you'll see a dial face with a large sweep hand and a small triangle or star.

  1. Shut off every water user in the house. That means faucets, the dishwasher, the washing machine, the ice maker, and the irrigation timer.
  2. Find the low-flow indicator. It's the small triangle or star on the meter face. On most Fort Pierce meters it spins at the slightest flow.
  3. Watch it for 60 seconds. If the triangle moves at all, water is passing through the meter.
  4. Write down the numbers. Note the sweep hand position and the gallon reading. Wait 30 minutes with everything still off, then read again.

If the reading climbed, you have a leak. If the triangle is still, the problem is likely a fixture that only runs intermittently - a toilet that refills on its own, or an irrigation zone that kicks on at 4 a.m.

The Water Meter Test for a Slab Leak in Fort Pierce

The water meter test for a slab leak in Fort Pierce is the same procedure, with one extra step: shut off the main valve at the house and test again. If the meter stops with the house valve closed, the leak is inside your plumbing - possibly under the slab. If it keeps spinning with the house valve closed, the leak is between the meter and the house, which is the utility's responsibility in most cases.

Here's the sequence we use on every call:

  • Test 1 - everything off, house valve open. Meter moves = active leak inside the home.
  • Test 2 - house valve closed. Meter still moves = leak on the service line, call the utility.
  • Test 3 - isolate the water heater. Close the cold inlet. If the meter stops, the leak is in the heater or its recirculation loop.
  • Test 4 - isolate the irrigation. Close the irrigation backflow preventer. If the meter stops, the leak is in the yard, not the slab.

When Tests 1 and 3 both show flow with the heater isolated, the leak is almost certainly under the slab. That's when we bring in acoustic listening equipment and thermal imaging to pinpoint the exact spot before anyone cuts concrete. Our slab leak detection in Fort Pierce Florida service typically locates the leak within 2 feet of accuracy, which keeps the repair patch small.

High Water Bill but No Visible Leak in Fort Pierce FL: What to Check Next

A high water bill but no visible leak in Fort Pierce FL is common with slab leaks because the water wicks into the sand and limestone under the slab instead of pooling on the floor. Before you assume the worst, rule out these four hidden culprits:

  • Toilet flappers. Put a few drops of food coloring in the tank. If color appears in the bowl after 15 minutes without flushing, the flapper is leaking. A $6 part can waste 200 gallons a day.
  • Irrigation valves. A stuck zone valve runs continuously and can add 500 gallons a day. Check for soggy spots in the yard at 6 a.m.
  • Water softener or whole-house filter. These backwash on a timer and can stick in the backwash cycle.
  • Pool autofill. A failed float valve keeps the pool topped off 24/7 and shows up as a steady bill increase with no puddle.

If all four check out and the meter still moves, the leak is under the slab. We see this often in slab leak repair Lakewood Park Fort Pierce FL, where 1990s ranch homes sit on shallow slabs over sandy soil that hides water quickly.

Signs You Have a Slab Leak Under Your Fort Pierce Home

Slab leaks in Fort Pierce announce themselves in ways beyond the bill. The most reliable signs are hot spots on the floor, the sound of running water when everything is off, and a foundation crack that appears or widens over a few weeks. Because Fort Pierce sits on sandy soil with a high water table, under-slab water often follows the path of least resistance and surfaces at the baseboard rather than the center of the room.

Watch for these:

  • Warm spots on tile or vinyl. A hot-water line leak under the slab heats the floor above it. You'll notice it barefoot.
  • The sound of running water at 2 a.m. Put your ear to the floor near the bathroom or kitchen. A hiss or rush means pressurized water is escaping.
  • Baseboards that cup or peel. Water wicking up the drywall shows as paint bubbling at the bottom 4 inches.
  • Musty smell in a room with no window. Trapped moisture under the slab feeds mold at the carpet tack strip.
  • A water bill that jumps 3,000 to 10,000 gallons in one cycle. That's the range we see on a typical under-slab line leak.

If two or more of those fit, stop running the meter test and call for under slab leak detection in Fort Pierce Florida. Continuing to run water through a leaking line erodes the soil under the slab and can turn a $900 pipe repair into a $6,000 foundation job.

Common Mistakes Homeowners Make With a Water Bill Spike

The most expensive mistake with a water bill spike is waiting for the next billing cycle to see if it "corrects itself." A slab leak does not heal. It grows. A pinhole that leaks 50 gallons a day in November can be leaking 500 gallons a day by February, and the water is carving a void under your foundation the whole time.

Other mistakes we see on service calls:

  • Blaming the utility first. Meter errors happen, but they're rare. Test your own plumbing before you dispute the bill.
  • Running the irrigation test wrong. Closing the backflow preventer is not the same as closing the zone valve. Test at the backflow.
  • Cutting concrete before locating. We've seen homeowners jackhammer a 4-foot square and miss the leak by 3 feet. Acoustic locating costs less than the concrete patch.
  • Ignoring the water heater. A leaking recirculation line under the slab mimics a slab leak and costs $400 to $700 to fix - far less than a slab repair.
  • Not checking the pool. In Fort Pierce, a pool autofill failure can add 1,000 gallons a day and look exactly like a slab leak on the meter.

One more: don't shut off the main and leave it off for days. Fort Pierce heat in the 90s plus a dry slab can cause tile to tent and grout to crack. If you have to isolate the leak, keep the house valve open and shut off only the affected branch.

When to Call a Professional for Leak Detection in Fort Pierce

Call a professional when the meter moves with every fixture off and the toilet, irrigation, pool, and water heater have all been ruled out. That combination points to a leak under the slab, and locating it requires equipment most homeowners don't own: acoustic listening discs, thermal cameras, and pressure-isolation gauges. We carry all three on every truck.

Our water leak detection in Fort Pierce Florida service starts with a meter test and a walkthrough, then moves to non-invasive locating. We find the leak, tell you the repair options, and give you a flat price before we cut anything. Most residential slab leaks in Fort Pierce run $900 to $2,400 in 2026 depending on access and whether the line is under tile or carpet. We patch the slab and pressure-test the line before we leave.

If you're in a neighborhood with older copper - slab leak repair Lincoln Park Fort Pierce FL is a good example - ask for a full pressure test on the whole system, not just the leaking branch. Where one pinhole has formed, others are usually close behind.

Frequently Asked Questions

Why is my water bill so high in Fort Pierce FL?

The most common causes are a leaking toilet flapper (200 gallons a day), a stuck irrigation valve (500 gallons a day), or a slab leak under the foundation (3,000 to 10,000 gallons per billing cycle). Run a meter test with everything off to narrow it down.

What is the water meter test for a slab leak in Fort Pierce?

Shut off every fixture and appliance, note the meter reading, wait 30 minutes, and read again. If the low-flow indicator moves, you have a leak. Close the house valve and repeat - if it still moves, the leak is on the utility side, not under your slab.

I have a high water bill but no visible leak in Fort Pierce FL. What now?

Check the toilet flappers with food coloring, the irrigation backflow preventer, the pool autofill, and the water softener backwash cycle. If all four are dry and the meter still spins, the leak is under the slab and needs acoustic locating.

Why is my water meter spinning when everything is off in Fort Pierce FL?

Water is moving through the meter, which means a pressurized line is leaking somewhere between the meter and your fixtures. Isolate the water heater and irrigation first. If the meter still spins, it's a slab leak or a service line leak.

How do I read a water meter to find a leak in Fort Pierce?

Lift the meter lid near the street, find the small triangle or star (the low-flow indicator), and watch it for 60 seconds with all water off. Any movement means flow. Write down the gallon reading, wait 30 minutes, and compare.

Get Help With Leak Detection in Fort Pierce

If your meter is spinning and you've ruled out the obvious, we'll find the leak and give you a flat repair price before we touch your floor. Call Pierce Leak Pros at 1234567890 to schedule slab leak repair Fort Pierce FL - most calls get a same-day or next-day visit.

Tagged with

#slab leak#water bill#leak detection#fort pierce#water meter

Common Questions

Why is my water bill so high in Fort Pierce FL?
The most common causes are a leaking toilet flapper (200 gallons a day), a stuck irrigation valve (500 gallons a day), or a slab leak under the foundation (3,000 to 10,000 gallons per billing cycle). Run a meter test with everything off to narrow it down.
What is the water meter test for a slab leak in Fort Pierce?
Shut off every fixture and appliance, note the meter reading, wait 30 minutes, and read again. If the low-flow indicator moves, you have a leak. Close the house valve and repeat - if it still moves, the leak is on the utility side, not under your slab.
I have a high water bill but no visible leak in Fort Pierce FL. What now?
Check the toilet flappers with food coloring, the irrigation backflow preventer, the pool autofill, and the water softener backwash cycle. If all four are dry and the meter still spins, the leak is under the slab and needs acoustic locating.
Why is my water meter spinning when everything is off in Fort Pierce FL?
Water is moving through the meter, which means a pressurized line is leaking somewhere between the meter and your fixtures. Isolate the water heater and irrigation first. If the meter still spins, it's a slab leak or a service line leak.
How do I read a water meter to find a leak in Fort Pierce?
Lift the meter lid near the street, find the small triangle or star (the low-flow indicator), and watch it for 60 seconds with all water off. Any movement means flow. Write down the gallon reading, wait 30 minutes, and compare.

Need slab leak detection in Fort Pierce? We'll find it today.

Our technicians run the meter test, locate the leak with acoustic and thermal equipment, and give you a flat repair price before any concrete is cut. Call Pierce Leak Pros and get your water bill back to normal.

Call 1234567890 Send a Message
Call 1234567890 Get Quote
Call Quote